Sma701 Headend System User Manual Ver 2 updated 14/08/2008 content

2. System Block Diagram

3. Structure & Character

SMA701MF（Main Frame with Power supply and fans）

SMA701CU（Control Unit）

SMA701PM-13S（QPSK/PAL decoder/modulation module with CI and TS output）

SMA701PM-13C（QAM/PAL decoder/modulation module with CI and TS output）

SMA701PM-13T（COFDM/PAL decoder/modulation module with CI and TS output）

SMA701RM-13D（Decoder/Modulation Module）

SMA-701CU

SMA-701CU is a hot-plug ‘keypad + display’ unit and is designed to connect to the SMA-701MF, the Main Frame, through a popular RJ11 phone wire. This connection provides the powering and signaling paths. Seventeen buttons with 16 X 4 characters LCD display let user to perform all necessary accesses to the system.

Control unit description

0~9 Num button，input the value of the menu or the number of the channel which you want to view.

Menu Call the menu and the command box

Exit Go back to the previous menu or exit the menu

OK Confirm the performance

▲&▼ Zapping or switch between the options of the menu

◄&► Decrease/Increase Volume or Moving Left /Right in the menu

Dimension of Control Unit：100mm*189mm*33mm

Note: Control Unit is for setting use, please disconnect it while finish setting.

4. Installation

The SMA701 can be installed into a standard EIA 19” rack, and could be mounted onto wall by put the left and right handles in different way of fixation.

4.1 Wall-mounting

Each bracket can support around 20KG.

Don’t put heavy stuffs on the top of the SMA701 main frame.

Face to the wall

fan

Picture 4.1 Handle Fixation for wall-mount

4. Operation Instruction

Power on the Control Unit, the screen will display below message:

Use ◄ or ► button to control each cassette, the 1^st row displays location and category of chosen cassette, for example:

2^nd row On Screen Display switch

3^rd row PAL RF modulation parameter setting

4^th row other settings

For example, by choosing SMA-701PM-13S module, it will display followings;

01: QPSK->PAL

OnScreen: Off

RF-Freq: 550,2MHz

Other:

Using the buttons to select 2^nd~4^th row can operate each parameter setting.

M
OnScreen: Off

ove the cursor to the 2^nd row on LCD by using ▼button, and use ◄or ►button to switch on the OSD (On Screen Display). On the Television set, select the channel corresponding to the RF frequency output by the cassette, you will see the OSD menu showed on screen. For operation on OSD menu, refer to Chapter 4.3.

To turn off the OSD menu, press Exit button until the OnScreen be turned “Off”.

Note: when the OnScreen is turn “On”, all the buttons on the control unit are only applicable for the OSD menu on the TV screen. Using the Exit button to exit OSD menu and continue the other settings with the control unit. Refer to chapter 4.4.
4.2.2 PAL Modulator Parameter Settings

3^rd row on control unit screen is for parameter settings of PAL modulator which contents 2 settings.

The range goes from 48.2 MHz to 860.2 MHz.

Note 1: the value after the comma CANNOT be edited.

Note 2: if the chosen value is out of the valid range, it will automatically turn back to the previous setting.

4.2.3 Module Message

4^th row on control unit screen is for other settings which contents 3 settings.

Language setting, currently, only English is available.

Show the version number of the MCU on the cassette.

E
Reset: No

For example, by choosing SMA-701PM-13S module and switch on the OnScreen option:

01: QPSK->PAL

OnScreen: On

RF-Freq: 550,2MHz

Other:

On the Television set, select the TV channel corresponding to the RF frequency output by the cassette, you will see the OSD menu showed on screen.

Picture 4.1 OSD Menu

Note: the OSD menu will close itself if no use for 1 minute. Press menu to call the menu back again.

TV Program Manage

Menu

Program Manager

Radio Program Manage

System Information

Audio Language

CI Multidecoding Setup

Picture 4.2 the menu structure for SMA-701PM-13x

• 
  Channel Manager
  
• 
  Installation
  
• 
  System Setting
  
• 
  System Information
  
• 
  Subtitle Language
  
• 
  Audio Language
  
• 
  Factory Default
  
• 
  Common Interface (ONLY for SMA701PM-13x)
  

4.3.1 Channel Manager

This menu consists of TV channel and Radio channel. Press the buttons to select TV Program Manage or Radio Program Manage, and press OK to enter.

To delete a program from the program list (in the TV or the Radio Program Manage) press the buttons to select the program and press the OK button to confirm. A cross will be displayed in front of the program name, and the program will not be shown in the program list during View Mode. Press the OK button again to cancel the deletion.

You can set the parameters for searching programs in the installation menu. Use the buttons to move the cursor, and use the buttons for editing the parameters.

For SMA701PM-13S, you need to enter the parameters of the

satellite/transponder for searching. Press the OK button to confirm the parameters

and start searching.

Frequency is therefore “04000”, and not “4000”.

During the search, you can press the Exit button to cancel the search.

4.3.2.1 Installation for SMA701PM-13T

For SMA701PM-13T, you need to enter the frequency for manual

search.

Press the OK button to confirm the parameters and start the search.

After the search is finished, press the OK button to confirm and

save the searched programs.

During the search you can press the Exit button to cancel the search.

The menu includes the following 6 submenus:

• 
  OSD Language
  
• 
  Audio Language
  
• 
  Subtitle Language
  
• 
  Subtitle Priority
  
• 
  Screen Mode
  
• 
  Audio Track
  

You can set the audio language for each cassette here.

Press the ► button, there will be a dialogue box pop up, type in

the abbreviation letters following DVB standard, press OK to

confirm. Then the audio language for all programs being

decoded by the cassette will be set to be the user setting.

For example, to set the English as the audio language, you

will type in ENG and press OK. Then English will be set

as the default audio language for each program decoded by the

cassette.

Note1: for that program which doesn’t content the audio in current set language, the first positioned audio will be output in other language.

Note2: there is another audio language setting option for the playing program, which may change the audio language in System Setting, refer to chapter 4.3.2.5 for more.

You can set the Subtitle language for each cassette here.

Press the ► button, there will be a dialogue box pop up, type in

the abbreviation letters following DVB standard, press OK to

confirm. Then the subtitle language for all programs being

decoded by the cassette will be set to be the user setting.

For example, to set the English as the subtitle language, you

will type in ENG and press OK. Then English will be set

as the default subtitle language for each program decoded by the

cassette.

Note1: for that program which doesn’t content the subtitle in current set language, the first positioned subtitle will be output in other language.
Subtitle Priority

There are two alternatives: EBU first or DVB first. Press the buttons to change the setting.

There are three alternatives: 4:3 Letter Box, 16:9 Full or Auto. Press the buttons to change the setting.

There are four alternatives: Auto, MONO, Dual or Stereo. Press the buttons to change the setting.

Note: Dual L and Dual R may carry different language which is up to the stream itself.

Note: the outputted audio may be language mixed when the L and R carry different language audio.

4.3.4 System Information

User can check the program information and the system configuration in this menu.

• 
  Program Information
  
• 
  System Config
  

Program Information

In this menu the following things can be seen: program name, program number, frequency, guard int, constellation, code rate, video PID, audio PID, PCR PID plus signal strength and quality.

System Config

The hardware version and software version can be seen

in this menu.

4.3.5 Subtitle Language

The subtitle language of the playing program can be changed in this menu.

All available subtitle languages contented in this program will be listed out, use the buttons to select subtitle language or turn it off, press OK button to confirm or press Exit button to scrap.

Note: the setting is only applicable for the current playing program, and when switch to another program and then switch back, the subtitle language will be automatically be set to the system setting.

4.3.6 Audio Language

The audio language can be changed in this menu.

All available audio languages contented in this program will be listed out, use the buttons to select audio language. Press OK button to confirm or press Exit button to scrap.

Note: the setting is not only applicable for the current playing program, but also for all the other programs being decoded by the cassette. And when the user change the setting in this menu, the same audio language setting will be automatically be set to the system setting.

4.3.7 Factory Settings

Press the buttons to select the factory setting and press

the OK button to enter.

Press the OK button to confirm, and a pop-up box will appear on the screen. Press the buttons to select OK to continue or select Cancel to stop.

During this process, you can press the Exit button to cancel.

4.3.8 Common Interface

(ONLY for SMA701PM-13x).

You can plug in the smart card and CAM module in order to watch scrambled programs. Press the OK button to enter the menu and press the Exit button to go back to the main menu.

Note: Please follow the screen guidance for the detailed operation method. All the operations are varied according to smart card and CAM Module.

4.3.9 CI Multidecoding Setup

(ONLY for SMA701PM-13x).

The SMA701PM-13x supports the multidescramble CAM.

Press the buttons to change the setting for programs being

decoded by the cassette. If a program is set as “Pass”, it will be

delivered out directly without being descrambled. If a program is

set as “decoding”, it will be delivered to the CAM for descrambling.

In this menu, only 8 programs can be listed each page. Press

the ▼ buttons to scroll down to next page for settings.

Note: the number of programs can be descrambled is depended on the CAM itself.

4.4 Other operation

Press Exit button until the OSD menu disappeared (but on the control unit, the OnScreen is On),

Use ◄ button to decrease volume or use ► to increase volume.

Use ▼▲ buttons to zapping between programs being decoded by the cassette.

5
MENU
. Notice in the use

• 
  If you want to replace or add the card of pattern, please do the operation after power off.
  
• 
  This product is suitable for indoor use only.
  
• 
  While insert or pull out cassette, try to position cassette to the main board connector
  

correctly in order to avoid connector damage.

• 
  Please keep ground connection well.
  
• 
  Please keep 10cm(or above) distance between each SMA-701MF while using more than
  

one SMA-701MF.

• 
  If you want to hang the machine on the wall , here has 4 hanging holes , each hole can
  

carry more than 10Kg .

• 
  The core of the signal cable is not suitable too long , it should be 2mm longer than the
  

screw cap .

• 
  There is current output from the LNB input interface , please do not connect the dummy
  

load on it .

• 
  We suggest connecting the dummy load (75Ω) to the LNB loop through interface.
  
• 
  We suggest connecting the dummy load (75Ω) to the RF input interface.
  
• 
  We suggest connecting the dummy load to the interface of the main-board in the
  

mainframe box .

• 
  Please build in the protection cap (RJ11) when the interface is not employed , it is for the
  

reason of damp proof.

• 
  If the machine word out of the way, please connect with the agent. Only the professional
  

people is allowed to open the mainframe box and process the installation and maintain .

6. Issues and Problem Solving

Please check on below before notifying vender for repair.
1. No RF signal output?

Answer: Check the power supply, fuse, and input tension.

2. Serious noisy in analog picture, here are some overlapped pictures?

Answer: Check the intensity of the neighbor channels, whether they are too strong or not; or frequency overlap; AC voltage too low; or there are disturbing sources around the machine.

3. Controller is of no effect?

Answer: Pull out and Plug in again, check the pin whether it has a bad touch or not.

4. The SMA-701PM-13S shows the intensity of the satellite signal is 0?

Answer: check the specification of the LNB. Is there a short circuit? Whether the power supply for the 0-22K/13V-18V is right? If there is short circuit, please cut the LNB, remove the short circuit, wait for 3-5 minutes, link the LNB again.

5. We can not access the card of pattern.

Answer: check whether the card of pattern has a bad touch or not.

This document and the information contained in it is the property of Pro Broadband Inc. and may be the subject of patents pending and granted. It must not be used for commercial purposes nor copied, disclosed, reproduced, stored in a retrieval system or transmitted in any form or by any means (electronic, mechanical, photocopying, recording or otherwise), whether in whole or in part, without Pro Broadband Inc.‘s prior written agreement.

© 2008 Pro Broadband Inc. All rights reserved.

Kataloq: assets -> files
files -> Privacy in the Workplace Paul Roth Faculty of Law University of Otago Introduction
files -> TỔng hợp dự kiến học bổng học kỳ (NĂm học ) CÁc khoá như sau
files -> Bank of baku səhmdar cəMİYYƏTİ 31 dekabr 2011-ci IL tarixinə bitən IL üzrə
files -> Azərbaycanda Milli Məsləhət Qrupunun Görüşü hesabat 11 Aprel 2014 Caspian Plaza, Bakı, Azərbaycan
files -> The distress act 1267 Private clamping and the Statute of Marlborough 1267, How is private clamping compatible with this Act?

Yüklə 94.7 Kb.

Dostları ilə paylaş: