Nzqa expiring unit standard 1563 version 7




Yüklə 34.89 Kb.
tarix16.04.2016
ölçüsü34.89 Kb.

NZQA Expiring unit standard

1563 version 7




Page of




Title

Clean floors

Level

2

Credits

4




Purpose

This unit standard is for people entering the cleaning industry.
People credited with this standard are able to: dustrol the floor; damp or wet mop the floor; and vacuum the floor.




Classification

Cleaning and Caretaking > Cleaning Skills




Available grade

Achieved


Explanatory notes
1 Competence demonstrated during assessment against this standard must comply with the requirements of:

Employment Relations Act 2000;

Health and Safety in Employment Act 1992;

Resource Management Act 1991.


2 Equipment and cleaning agents must be used in accordance with manufacturer's recommendations.
3 Definitions

Health care facilities can include aged residential care facilities, dental surgeries, doctors’ surgeries, specialist clinics, general and specialist hospitals.

Dustrol may also be called a static mop or dust mop. While the technical applications vary between each of these, the principles are the same. The purpose is to remove dust from the floor without creating dust showers.

Flat mop is a type of microfibre mop and can be used in a wet or dry condition.

Mop refers to either a string/cotton, sponge or microfibre type, or a flat mop.

Industry best practice refers to any enterprise and/or establishment requirements, practices, policy, procedures, methods and protocols which are in accordance with applicable legislation, regulations and New Zealand Standards.
4 A vacuum cleaner used in health care facilities must be fitted with a genuine HEPA (High Efficiency Particulate Air) filter.
5 When this standard is used in health care facilities, the assessor and trainees need to be aware of the facility’s policies and protocols that must be adhered to.
Outcomes and evidence requirements
Outcome 1
Dustrol the floor.
Evidence requirements
1.1 Equipment is either selected individually or from single station equipment and is clean and in working condition.
Range may include – dustrol, dustpan and hand brush, vacuum.

Evidence of dustrol and one other is required.


1.2 Loose soil is removed without creating dust showers and dustrolled floor is free from dust and loose soil.
1.3 Equipment is cleaned, checked and stored in accordance with industry best practice.
Outcome 2
Damp or wet mop the floor.
Evidence requirements
2.1 Equipment is either selected individually or from single station equipment and is clean and in working condition.
Range mop, bucket and/or wringer.
2.2 Warning signs are displayed in accordance with industry best practice.
Range at least one of – signs, cordons, barriers.
2.3 Complete coverage with cleaning solution is achieved.
2.4 Condition of mop and solution ensures that cleaning level is maintained throughout the task.
Range solution changed to maintain level of cleaning.
2.5 Task is completed without damage or risk to personnel, furnishings, or fixtures.
2.6 Equipment is cleaned, checked and stored in accordance with industry best practice.
Outcome 3
Vacuum the floor.
Evidence requirements
3.1 Selected equipment is clean and in working condition.
Range vacuum cleaner, attachments, dustpan, hand brush.
3.2 Vacuum cleaner is safety checked and damaged and non-operational equipment reported in accordance with industry best practice.
3.3 Floor is cleared of large soil deposits before vacuuming begins.
3.4 Accessories are used which are compatible with floor surface and location of soil and dust.
Range corners, edges, open floor.
3.5 Task is completed leaving floor free from visible soil and dust.
3.6 Task is completed without damage or risk to personnel, furnishings, or fixtures.
3.7 Equipment is cleaned, checked and stored in accordance with industry best practice.



Replacement information

This unit standard, unit standard 1565, unit standard 1566, unit standard 1569, unit standard 7182, unit standard 17263, and unit standard 17264 have been replaced by unit standard 28350 and unit standard 28352.


This unit standard is expiring. Assessment against the standard must take place by the last date for assessment set out below.
Status information and last date for assessment for superseded versions

Process

Version

Date

Last Date for Assessment

Registration

1

26 May 1994

31 December 2014

Review

2

31 August 1996

31 December 2014

Review

3

27 April 2000

31 December 2014

Revision

4

8 February 2001

31 December 2014

Review

5

27 February 2006

31 December 2014

Review

6

18 October 2012

31 December 2017

Review

7

17 July 2014

31 December 2017




Consent and Moderation Requirements (CMR) reference

0004

This CMR can be accessed at http://www.nzqa.govt.nz/framework/search/index.do.
Please note

Providers must be granted consent to assess against standards (accredited) by NZQA, before they can report credits from assessment against unit standards or deliver courses of study leading to that assessment.


Industry Training Organisations must be granted consent to assess against standards by NZQA before they can register credits from assessment against unit standards.
Providers and Industry Training Organisations, which have been granted consent and which are assessing against unit standards must engage with the moderation system that applies to those standards.
Requirements for consent to assess and an outline of the moderation system that applies to this standard are outlined in the Consent and Moderation Requirements (CMR). The CMR also includes useful information about special requirements for organisations wishing to develop education and training programmes, such as minimum qualifications for tutors and assessors, and special resource requirements.

Careerforce

SSB Code 101814



Ó New Zealand Qualifications Authority 2016




New Zealand Qualifications Aut





Verilənlər bazası müəlliflik hüququ ilə müdafiə olunur ©azrefs.org 2016
rəhbərliyinə müraciət

    Ana səhifə