Nzqa expiring unit standard 1316 version 8




Yüklə 32.72 Kb.
tarix11.03.2016
ölçüsü32.72 Kb.

NZQA Expiring unit standard

1316 version 8




Page of




Title

Perform seaming and finishing operations in canvas fabrication

Level

3

Credits

12




Purpose

This unit standard is for people who work in the canvas fabrication and allied industries. People credited with this unit standard are able to: seam the work for canvas fabrication; perform finishing on the work for canvas fabrication; demonstrate knowledge of fasteners and fittings for canvas fabrication; and select and fit fasteners and fittings for canvas fabrication.




Classification

Outdoor Fabric Products > Canvas Fabrication




Available grade

Achieved


Explanatory notes
The following legislation (and subsequent amendments) is applicable to this unit standard and must be followed where applicable:

– Health and Safety in Employment Act 1992.


Outcomes and evidence requirements
Outcome 1
Seam the work for canvas fabrication.
Evidence requirements
1.1 Seam type is selected to client specification and company policy.
Range plain single seam, top sewn seam, double top sewn seam, run and fell seam, folded overlap seam.
1.2 Sewing machine is selected and prepared to produce specified seam according to machine manufacturer’s specifications and company policy.
1.3 Reinforcements are attached according to client specification and company policy.
1.4 Work is positioned and joined to line at workplace required speed, using stitch length for the material being sewn and the strength of seam required.
1.5 Safe working practices are carried out throughout the task.
Range personal safety; safety of other people; workshop safety; tool, equipment, and machine safety.
Outcome 2
Perform finishing on the work for canvas fabrication.
Evidence requirements
2.1 Hemming is carried out to client specification and company policy.
Range single hem on selvedge edge, double turned hem.
2.2 Bias binding is sewn according to company policy.
2.3 Ropes are attached as specified by client and according to company policy.
2.4 Safe working practices are carried out throughout the task.
Range personal safety; safety of other people; workshop safety; tool, equipment, and machine safety.
Outcome 3
Demonstrate knowledge of fasteners and fittings for canvas fabrication.
Evidence requirements
3.1 Type and size identify fasteners and fittings are identified according to manufacturer’s specifications.
Range eyelets, domes, turnbuckles, rivets, studs, hooks, shock cord fastenings, rope end and splice clips, hook and loop, stayput, lift the dot, buckles, zippers, sister clips, overcentre buckles, cam buckles, rave hooks, grommets, rings, press rings.
3.2 Applications for the fasteners and fittings are described according to manufacturer’s specifications.
3.3 Methods for attaching the fasteners and fittings are described according to manufacturer’s specifications.
Outcome 4
Select and fit fasteners and fittings for canvas fabrication.
Evidence requirements
4.1 Fasteners and fittings are selected to job specification requirement.
4.2 Fasteners and fittings are attached to the product at the workplace required speed in positions dictated by the job specification requirements, using correct machines and tools.
4.3 Attachment of fasteners and fittings conform to workplace procedures.
4.4 Safe working practices are carried out throughout the task.
Range personal safety; safety of other people; workshop safety; tool, equipment, and machine safety.



Replacement information

This unit standard has been replaced by unit standard 23481, unit standard 23482, unit standard 23483, and unit standard 23484.


This unit standard is expiring. Assessment against the standard must take place by the last date for assessment set out below.
Status information and last date for assessment for superseded versions

Process

Version

Date

Last Date for Assessment

Registration

1

3 August 1995

31 December 2016

Revision

2

16 September 1997

31 December 2016

Revision

3

4 November 1997

31 December 2016

Revision

4

28 May 1998

31 December 2016

Review

5

17 August 1999

31 December 2016

Review

6

26 March 2007

31 December 2016

Rollover

7

19 November 2010

31 December 2016

Rollover

8

20 November 2015

31 December 2020




Consent and Moderation Requirements (CMR) reference

0014

This CMR can be accessed at http://www.nzqa.govt.nz/framework/search/index.do.
Please note

Providers must be granted consent to assess against standards (accredited) by NZQA, or an inter-institutional body with delegated authority for quality assurance, before they can report credits from assessment against unit standards or deliver courses of study leading to that assessment.


Industry Training Organisations must be granted consent to assess against standards by NZQA before they can register credits from assessment against unit standards.
Providers and Industry Training Organisations, which have been granted consent and which are assessing against unit standards must engage with the moderation system that applies to those standards.
Consent requirements and an outline of the moderation system that applies to this standard are outlined in the Conesnt and Moderation Requirements (CMR). The CMR also includes useful information about special requirements for organisations wishing to develop education and training programmes, such as minimum qualifications for tutors and assessors, and special resource requirements.

NZ Motor Industry Training Organisation (Incorporated)

SSB Code 101542



Ó New Zealand Qualifications Authority 2016





Verilənlər bazası müəlliflik hüququ ilə müdafiə olunur ©azrefs.org 2016
rəhbərliyinə müraciət

    Ana səhifə