Nzqa expiring unit standard 1315 version 8




Yüklə 31.86 Kb.
tarix11.03.2016
ölçüsü31.86 Kb.

NZQA Expiring unit standard

1315 version 8




Page of




Title

Handle and identify materials used in canvas fabrication

Level

3

Credits

3




Purpose

This unit standard is for people who work in the canvas fabrication and allied industries. People credited with this unit standard are able to: demonstrate knowledge of materials for canvas fabrication; run out, check and cut material for canvas fabrication; and finish rope work for canvas fabrication.




Classification

Outdoor Fabric Products > Canvas Fabrication




Available grade

Achieved


Explanatory notes
The following legislation (and subsequent amendments) is applicable to this unit standard and must be followed where applicable:

– Health and Safety in Employment Act 1992.


Outcomes and evidence requirements
Outcome 1
Demonstrate knowledge of materials for canvas fabrication.
Evidence requirements
1.1 Fabric used in workplace is identified by type and categorised into light, medium and heavy grade.
Range polyvinyl chloride (PVC), canvas, polyethylene (P.E.), nylon, acrylic, polyester, cotton duck, jute, leather, polyester cotton, linen flax, polypropylene.
1.2 Fabric construction terminology is used correctly according to manufacturer’s specifications and company policy.
Range warp, weft, bias, selvedge.
1.3 Rope and cord used in workplace is identified by size, material and construction according to manufacturer’s specifications.
1.4 Webbing, binding tape and bias binding used in workplace are identified by size and material according to manufacturer’s specifications.
1.5 An end use of the material is described according to manufacturer’s specifications and company policy.
Range materials listed in 1.1, 1.3, 1.4 above.
Outcome 2
Run out, check and cut material for canvas fabrication.
Evidence requirements
2.1 Material is selected to job specification, run out on bench and checked for defects and cleanliness, under supervision according to company policy.
2.2 Material is cut to given line using tool for the material and at workplace required speed.
Range scissors, hot knife, electric knife, plain knife, wheel cutter, leather knife.
2.3 Unused material and offcuts are stored according to company policy.
2.4 Work area is cleared and cleaned to ensure safe operating conditions according to company policy.
Range bench, floor, exits, machine space.
2.5 Safe working practices are carried out throughout the task.
Range personal safety; safety of other people; workshop safety; tool, equipment, and machine safety.
Outcome 3
Finish rope work for canvas fabrication.
Evidence requirements
3.1 Ropes are cut to length with splicing and finishing allowance according to company policy.
3.2 Rope ends are finished according to company policy.
Range whipping, crown knot, crimping.
3.3 Ropes are spliced according to specification and company policy.
Range eye splice, crimped eye, short splice, long splice, tapered splice.
3.4 Safe working practices are carried out throughout the task.
Range personal safety; safety of other people; workshop safety; tool, equipment, and machine safety.



Replacement information

This unit standard has been replaced by unit standard 23495.


This unit standard is expiring. Assessment against the standard must take place by the last date for assessment set out below.
Status information and last date for assessment for superseded versions

Process

Version

Date

Last Date for Assessment

Registration

1

3 August 1995

31 December 2016

Revision

2

16 September 1997

31 December 2016

Revision

3

4 November 1997

31 December 2016

Revision

4

28 May 1998

31 December 2016

Review

5

17 August 1999

31 December 2016

Review

6

26 March 2007

31 December 2016

Rollover

7

19 November 2010

31 December 2016

Rollover

8

20 November 2015

31 December 2020




Consent and Moderation Requirements (CMR) reference

0014

This CMR can be accessed at http://www.nzqa.govt.nz/framework/search/index.do.
Please note

Providers must be granted consent to assess against standards (accredited) by NZQA, or an inter-institutional body with delegated authority for quality assurance, before they can report credits from assessment against unit standards or deliver courses of study leading to that assessment.


Industry Training Organisations must be granted consent to assess against standards by NZQA before they can register credits from assessment against unit standards.
Providers and Industry Training Organisations, which have been granted consent and which are assessing against unit standards must engage with the moderation system that applies to those standards.
Consent requirements and an outline of the moderation system that applies to this standard are outlined in the Conesnt and Moderation Requirements (CMR). The CMR also includes useful information about special requirements for organisations wishing to develop education and training programmes, such as minimum qualifications for tutors and assessors, and special resource requirements.

NZ Motor Industry Training Organisation (Incorporated)

SSB Code 101542



Ó New Zealand Qualifications Authority 2016





Verilənlər bazası müəlliflik hüququ ilə müdafiə olunur ©azrefs.org 2016
rəhbərliyinə müraciət

    Ana səhifə