H. B. Fuller Ges m. b. H product information




Yüklə 16.03 Kb.
tarix09.03.2016
ölçüsü16.03 Kb.




H.B.Fuller Ges.m.b.H

PRODUCT

INFORMATION


INTRAFOLâ L 1135/43


Type of product:

Solvent-based primer

areas of application:

INTRAFOLâ L 1135/43 is a suitable primer for furniture films and edges made of PVC and thermosetting materials. 1-component or 2-component processing, depending on application.

special properties:

INTRAFOLâ L 1135/43 is non-blocking. Performance of INTRAFOL coating effective for at least 2 years.

Bonding with EVA- and PA-hotmelts and with dispersion-type systems. Bonding with UF-type glues only for thermosetting films.



PRoduct specification:

COMPONENT A:

INTRAFOLâ L 1135/43

solid contents:

approx. 11%

Density:

approx. 0.86 g/cm³ (20°C)

color:

white, coloring on request

VIScOSITy:

approx. 25 s (DIN-cup 4 mm, 20°C)

Hazard. goods classif.:

see Safety Data Sheet /label

storage:

6 months .

behaviour in cold:

thickens at temperatures below 10°C, but fully reusable after tempering in a water bath.







COMPONENT B:

HÄRTER 2

ISOCYANATE CONTENT:

approx. 13.3 %

Density:

approx. 1.17 g/cm³

color:

yellowish

VISCOSITY:

approx. 1600 mPas (20°C):

storage:

12 months, do not store at temperatures below 5°C

Hazard. goods classif.:

see Safety Data Sheet


instructions for use:

MIXING RATIO:

100 : 3




POT LIFE:

approx. 8 hours

MINIMUM CURING TIME:

approx. 2 days

WORKING TEMPERATURE.:

Application at room temperature

APPLICATION PROCEDURE AND TYPE OF APPLICATOR:

Roller coater systems

COVERAGE:

20 - 40g wet/m² ,

DILUTION:

Isa-Verdünner 220

CLEANING AGENT:

Isa-Verdünner 220

working instructions:

PREPARATION:

1-component for PVC furniture edges

2-component for edges, based on thermosetting materials and PVC membrane-press-film


Stir INTRAFOLâ L 1135/43well and - if necessary - mix with 3% Härter 2.

PROCESSING

Apply a thin and uniform layer of INTRAFOLâ L 1135/43with roller coaters, coverage approx. 20 - 40 g wet/m².

The drying temperature depends on the heat resistance of the substrate.

Standard value 45...60 s/70°C.

Cool down coated film to room temperature before unrolling.

When mixed with hardener, store primed material at room temperature during the first 48 hours and bond at the earliest 48 hours after primer application.

SPECIAL ATTENTION
Avoid friction of the coating caused by too harsh movement over metal parts or by friction of the transport rolls when guiding the substrate.
Härter 2 contains isocyanate. See EU-Safety Data Sheet.

Status: tt.06.jjjj (replaces all prior editions)

Issued by: SBU Assembly, Lab. Dept.


Printed on: 3/9/2016
Please note :

The information, specified in this Product Information, is based on careful laboratory tests and prevailing practical experience.

The information is not binding, which is also generally true for our practical customer service, given verbally, in writing and by tests, since, on account of the versatility of applications and use, also including possible industrial property rights of third parties, we cannot assume any responsibility.

Analysis results and all information regarding state and suitability of our products are only guidelines with no obligation on our part, unless they have been guaranteed expressly in writing, and above all do not represent a guarantee for specific properties.

We advise determining the suitability of our products with respect to their suitability for the intended use and application technology by adequate further testing.

In addition to the above, our General Sales and Delivery Conditions are applicable.


H.B. Fuller Austria Ges.m.b.H.

Kaplanstraße 30

A-4600 Wels

Tel.: +43 / 7242 / 409-0



Fax.: +43 / 7242 / 409-349


/ARi Page 1(2)



Verilənlər bazası müəlliflik hüququ ilə müdafiə olunur ©azrefs.org 2016
rəhbərliyinə müraciət

    Ana səhifə